Embedding Accessories
Electron Microscopy Sciences T-Sue™ Precast Paraffin Block, 2 mm
Precast T-Sue Microarray paraffin blocks are used to construct a tissue array block in minutes by simply punching the donor tissue cores and inserting into a pre-made paraffin recipient block. It is an easy, convenient, and low cost method for constructing paraffin tissue microarrays. The blocks are made of paraffin and the cassettes are made of acetal. The cassette is permanently bonded to the block and has consistent core diameters. It is ready to accept cores from the donor block.
Kit includes 6 Precast T-Sue Paraffin blocks and two punch needles with stylet.
Size: 2 mm
Capacity: 60 cores
Electron Microscopy Sciences Flat Embedding Mold Small Flat Embedding Mold, 4 mm deep, 10 x 6 mm
A clear silicone rubber with very high tear strength. It can be reused more times than the conventional silicone molds. It is resistant to most epoxy resins and its clear base allows positioning of the specimen lighted from beneath. This mold produces 12 embedding blocks with tapered ends.
Depth: 4 mm
Size: 10 x 6 mm
Cavities: 12
Electron Microscopy Sciences Double End Flat Embedding Mold with Cocoon Box
No more stickiness with new storage boxes. Most resins are no longer a challenge to flat embed when used in combination with the Cocoon box. The system withstands temperatures up to 70 Degrees C, and our flat embedding of many resins is made easier.
Electron Microscopy Sciences Paraffin TMA Arraymold Kit 1 (A +B), 2.0 and 1.5 mm diameter
The Arraymold is the simple tool for laboratories to perform Paraffin tissue microarrays (TMAs) with less time while maintaining excellent results. Process up to 150 specimens onto one single slide with very little time consuming, minimal technical training. The DVD instruction is accompanying with each kit, will step by step guide you to perform through the entire TMAs process.
Arraymolds allow pathologist or researcher to view many different samples on the same single slide.
Helpful in finding IHC markers for control or quality assurance from hundreds of samples.
Staining markers will be more consistent when hundreds of samples are on one slide.
Used less costly antibody.
Arraymold kit is small enough to be stored in a drawer.
Rubber arraymold can be reused many times without losing its flexibility. This package includes two Arraymold kits, Kit A and Kit B.
Diameter: 2.0 and 1.5 mm
Electron Microscopy Sciences Crystalbond™ 590 Adhesive Stick, Brown 225 GR
A temporary adhesive. These wash away adhesives are used as a temporary bond for holding delicate crystals, metallurgical specimens, glass components, and ceramic substrates for dicing, slicing, drilling and polishing. These materials adhere readily to metals, glass, ceramic and then can be washed after machining away using various solvents. For precise high purity work offers maximum adhesion to subminiature parts.
Color: Brown
Softening: 257°F (125°C)
Flow point: 302°F (150°C)
Viscosity: 9,000 cps
Electron Microscopy Sciences Embedding Shelf for Shandon
This removable shelf can be installed below the opening of the cryostat in the most convenient and location available. The selves can be made in various sizes to accommodate most instruments.
Electron Microscopy Sciences Flat Embedding Mold 3 mm with Cocoon Box
No more stickiness with new storage boxes. Most resins are no longer a challenge to flat embed when used in combination with the Cocoon box. The system withstands temperatures up to 70 Degrees C, and our flat embedding of many resins is made easier.
Electron Microscopy Sciences Cold Embedding Silicone Mold for Acylic Resin 40 mm
This mold is for acrylic resins only and the best mounting cup for all of our acrylic resins. The flexible silicone rubber makes it very easy to remove the mount from the mounting cup.
Diameter: 40 mm
Electron Microscopy Sciences Mold Release for Mounting Press 8 GR
Mold release agent to be used with mounting press.
Electron Microscopy Sciences Embedding Mold, Dykstra
EMS Embedding Mold is a new mold designed with Michael J. Dykstra Ph.D. from North Carolina State University Department of Veterinary Medicine. This Mold produces blocks of the best dimension to be held securely by Reichert/Leica Ultracut stepped microtome chucks. There are 24 cavities and the depth of each cavity is 4 mm which will prevent breakage of the blocks during razor blade trimming. Mold Measurements: 3 3/8" x 3" (85 x 77 mm. Cavity Measurements: 15 mmx 7 mm x 4 mm deep
Electron Microscopy Sciences Thompson Monolayer Embedding Mold
This mold used for embedding mammalian cells in monolayer culture in preparation of sectioning for light or electron microscopy. Tissue culture monolayer embedding molds eliminate the need for traditional BEEM capsules. The improved molds can be used to transfer the majority of cells from the entire surface of a cover slip to avoid losses of large amounts of cellular information occurring only randomly. In addition, other problems such as surface blemishes caused by air entrapment associated with BEEM capsules are eliminated.
Newcomer Supply Embedding Tissue Tampers Combo, 1 - 10mm x 10mm & 1 - 16mm x 19mm
Newcomer Supply’s Tissue Embedding Tampers are unique tools for flattening tissue sections in an embedding mold with ease! The design allows for the end-user to either use a forceps or their fingers to easily control the tampers. The aluminum, one piece handle extends 24mm above the tamper base and comes with a vinyl cap to help remain cool to the touch. There is also an anodized colored surface on the tamper that makes it more durable and corrosion-resistant. The tampers comes in two different sizes to accommodate small, medium and large embedding molds: 10mm x 10mm base (orange) and 16mm x19mm base (green). A combo pack is also available including 1 of each size.
